Wireless control system   | Home Your Cart | Contact Us

Wireless Controls

Security Remotes
Multi-channel Receivers
PIR Motion Detector
Smoke Detector
Carbon Monoxide Detector
 
Universal Industrial
Single Channel System
Two Channel System
Four Channel System
Two Way Systems

Heavy Duty Industrial

Single Channel System
Four Channel System
16  Channel System
 
Accessories
Antennas
Power Supplies
Connectors & Cables
Timers Relays
 

   

 Full Range of Professional Control Products!

 

8 Channel  Digital Remote Control  RECEIVER
 Up to 900 Feet 
  ( 300 m )  of Line-of-Sight Range with Panel-mount antenna kit

                   
 

  936008  $159.99

 

FEATURES
 Measured Line-of-Sight Range of 700 Feet
 Quick-Learn Programming
 Selectable Supervision
 Individual Outputs Per RF Channel and for Alarm, Low
 Battery, and Status.  7-Segment Channel Display
LED Indication for Alarm, Low Battery, and Status
Over one million factory pre-set codes are available and all receivers "learn" the transmitter ID
  Compatible Transmitters 
1 Channel handheld 
4 Channel handheld
8 Channel handheld
1 Channel stationary
PIR Motion detector
2 Channel Keychain

Smoke Detector
CO carbon monoxide detector
.
SPECIFICATIONS
Number of Channels: 8-Channels, supervised
 Receiver Carrier Frequency: 315 MHz  Bandwidth: 400 KHz typical
 Receiver Sensitivity: -102 dBm typical at each antenna
 Modulation: Type A1D, PPM (pulse position modulation)
 Measured Range: 1,500 feet typical, with most standard  stationary transmitters
 Loop response  2 seconds min
 Transmitter Capacity: 32 total with any distribution between channels 
(Note: learning multiple transmitters into any channel will defeat device supervision)
 Receiver Outputs: Open collector  4-Channel alarm outputs, one common low battery output,
 Factory set to normally open; can be globally selected as normally closed by internal jumper
 Current Rating: 100 mA maximum per output point, add power relay
 
Output jumper select for each channel
 Momentary: 4-second momentary closure on alarm
 Toggle: Alternate alarm action (toggle on, toggle off)
 Option jumpers select Momentary, Toggle or Latched output per channel
 Latch: Requires manual reset at receiver, or operates as a follower with  transmitter


DISPLAY OUTPUT
Channel Display: One 7-segment LED indicator; displays flashing center dash in power on an standby; displays channel ID during alarm condition along with alarm condition LED; automatically clears when alarm output restores; displays "P" and channel ID during programming mode
 RF Activity: Indicated by decimal point on 7-segment display; indicates radio receiver activity; flashes with received data
 Alarm Condition: Three LED indicators - alarm, low battery, and status;
displays conditions with corresponding channel ID
Operating Voltage: 10.2 to 14.4 VDC or 12 to 16 VAC
 Operating Current: Standby: 30 Ma; Alarm: Up to 120 mA
 Operating Temperature: 32° to 140° F (0° to 60° C)
 Dimensions: 7.25 in L x 1 in W x 5 in H (185 x 25.4 x 127 mm)
 Space Required for Installation: 7.5 in L x 14.0 in H
 Antenna: Two, 9-1/2 in wire whip antenna (supplied)
 Mounting Hardware: Four #6 x 1 1/4 in wood screws (supplied)
 

Receiver Operating Parameters:
 Status Supervision: Monitored on each channel for hourly status transmissions, reports status exception if no transmissions received within last 8-hour time period; one common status output provided for all channels; 7-segment display indicates channel where violation occurred; exception set and cleared by channel
 Enable Options: Status supervision enabled per channel; status enabled by cutting proper jumper per channel; factory default disabled; Note: with status supervision monitoring, it is not recommended to have more than one transmitter learned per channel
 Low Battery Supervision: Monitors each transmitter for low battery alarm; reports if any learned transmitter low battery signal received; one common low battery output for all transmitters; 7-segment display indicates channel where low battery occurred; low battery set and cleared by individual transmitters; transmitter that sends low battery report must send a good battery signal to clear low battery condition
 Program Mode: Enabled by program jumper; remove to enter program mode
 Transmitter Learn: Momentary press and release desired channel learn button; activate transmitter with five seconds to learn it into desired channel
 Memory Erase: Hold appropriate channel learn button for more than 10 seconds and release; transmitters learned into that channel will be erased from receiver memory  Memory Interrogation: Hold appropriate channel learn button for more than five and less than 10 seconds; alarm LED will flash the number of transmitters learned into selected channels    

Options
Power adapter 12V Power relay 10A  Power relay 30A   Latch relay 12V

Warning: Radio control equipment is not to be used in life safety

We accept PayPal and Credit Cards Thrue PayPal

Home Your Cart | Contact Us
 Copyright 2011 Allied Enterprises